Accessories

With a length of up to 90cm, the robust and high-quality tongs are the ideal working aid for larger aquariums.

No network access at your aquarium? Here is the Wi-Fi solution!

The optional CleanCover provides splashwater protection and is made of highly transparent, ultra-thin, impact-resistant plastic. It also protects your LED bars from limescale and dirt deposits and is very easy to clean.

High-performance LED switching mains adapter for operating our LED lighting bars (12V DC)

The holders to allow our LED bars to be mounted in your existing waterproof tube sockets.

Simple, minimalistic supports for LED bars

Unique lamp housing – individually and flexibly adjustable to your needs.

The LED adapter profile replaces your existing conventional T5 or T8 batten fittings 1 for 1

For manual dimming of the brightness of the LED bar(s) via rotary knob or remote control.

DIMIX6 is a manual 6-channel dimmer for stepless dimming and mixing of the connected LED bars and light colours.

The premium lighting control for novices and professionals!

The smart light control, simple to use, large range of functions!

With the SIMU-LUX daylight simulator, you can program and simulate your own and individual daily lighting routine.

Our smallest model offers all the basic functions of a light control system - simplicity in operation!

This distributor allows several LED lighting bars to be operated with a single mains adapter (assuming the power output is adequate).

 

Rubberised premium cable for extending the connection cables on our LED bars.

Heat-shrink solder connector for extending connection cables:
Connect - solder - insulate - seal - in one simple working process.

Adapters to connect LED lamps and, if necessary, mains adapters manufactured by third parties to our dimmers, light control and daylight simulation systems.

Various individual parts which you will find helpful for customised installations and uses

Suitable for use with appropriate control devices, such as a GHL Profilux.

For mounting up to 2 additional LED strips when using the T5/T8 holders or the DUO Adapter as a main holder.

For mounting the LED lighting with minimal space, e.g. under the sliding cover

The solenoid valve for night shutdown can be switched with our light controls.

This CO2 diffuser dissolves up to 98% of the CO2 in the aquarium water thanks to its fine ceramic membrane. Available in 3 sizes.

The lighting control system should be ready to go immediately? Then the "programming service" is just right for you!

Send the gift of light! Our high-quality printed gift vouchers are sent to you by post in an inconspicuous envelope. (To the value selected)

Perfect for attaching our light controls to the wall or ceiling of the aquarium cabinet. Without drilling!

For broadband high-frequency interference suppression of electrical loads with earth contact connection.

The High-Power-Solution allows a connected load of up to 480W (-10%) per channel on one SunRsier.

Suitable for insertion into a corresponding carrier profile or lamp profile or for individual mounting.

For connecting 2 LED bars or 2 temperature sensors to one channel of a light control

For using the aquaLUMix as a top or drop light.

For easy bundling and guidance of cable lines.

Different options for water supply of water cooling system are available.

A very small and economic pump for operating the water cooling system

For cleaning the LED bar cooling system

For fast and simple cleaning the cooling system by air pressure

Enables the use of the water cooling system for seawater aquariums

Side-mounted lamp = supported on the sides (glass edges) of the aquarium.

Supported on the cover plate or glass struts on the aquarium, and between these, depending on the cover and the aquarium. (See photos)

Lamp hanging freely above the aquarium, fastened by steel suspension wires to the ceiling.

Connect two lamp housings next to one another

Various lamp housings can be connected to one another and extended.

To replace light bars and cover flaps, the frame of the existing cover is still used.

For temperature monitoring, the sensor returns the temperature value of water and/or air to the SunRiser 8 in °C.

For mounting the LED lighting with minimal space, e.g. under the sliding cover

Additional holding bridges for individual mounting of several (shorter) LED bars

For manual dimming of the main light of a powerBEAM suspended lamp when automatic light control is not required.

The reflector serves as an anti-glare shield and maximizes the lighting intensity especially in the front or rear edge areas of the aquarium. 

With this set, up to 6 LED bars can be easily attached to the original aquatlantis support profile.

With this set, up to 6 LED bars can be easily attached to the original aquatlantis support profile.

For mounting up to 2 additional LED strips when using the T5/T8 holders or the DUO Adapter as a main holder.

Thanks to these guide rails, cover panels can be slid onto the aquarium easily and comfortably.

For easy and flexible mounting of the lighting, also inside a cover.